[Identification method of 2-methylisoborneol and geosmin in water by purge and trap-gas chromatography-mass spectrometry].

OBJECTIVE: To establishe an analysis and identification method for 2-methylisoborneol(2-MIB) and geosmin(GSM) in water using purge and trap-gas chromatography-mass spectrometry. METHODS: The samples were enriched and analyzed using a purge and trap system, followed by the separation on a DB-624(30 m×0.25 mm, 1.4 µm) chromatographic column. Quantification was performed using gas chromatography-mass spectrometry with the selected ion monitoring and internal standard calibration. RESULTS: The calibration curves for 2-MIB and GSM showed an excellent linearity in the range of 1 to 100 ng/L with R~2 values greater than 0.999. The detection limit and quantification limit for both 2-MIB and GSM were 0.33 ng/L and 1.0 ng/L, respectively. Spike recovery experiments were further carried on the source water and drinking water at three concentration levels. It showed that the average recoveries were from 82.0% to 111.0% for 2-MIB while 84.0% to 110% for GSM. Additionally, the test precision of 2-MIB and GSM ranged from 1.9% to 7.3% and 1.9% to 5.0%(n=6), respectively. The analysis of multiple samples including the local source water, treated water and distribution network water confirmed the existence of 2-MIB and GSM. CONCLUSION: Compared to the national standard(GB/T 5750.8-2023), the proposed method enables fully automated sample introduction and analysis without the extra pre-treatment. It provides the advantages of simplicity, good repeatability and high accuracy.

Detection and application of hypochlorous acid in both aqueous environments and living organisms.

The scarcity of water resources has raised concerns regarding drinking water safety. Excessive addition of hypochlorous acid (OCl-) as a disinfectant in drinking water can result in severe consequences. Moreover, abnormal levels of OCl- within the human body can lead to various diseases. Employing fluorescence analysis, the design and synthesis of specific fluorescent probes for simultaneous detection of OCl- in water environments and living organisms holds strategic significance in ensuring the safety of drinking water and mitigating potential risks caused by its abnormal concentrations. This article utilizes naphthalimide as a precursor to develop a novel probe enabling highly sensitive detection of OCl- in water environments and at the organelle level within living organisms. This endeavor serves to provide assurance for drinking water safety and offers health alerts.

DNA damage in inhabitants exposed to heavy metals near Hudiara drain, Lahore, Pakistan.

The current study was conducted on the inhabitants living in the area adjacent to the Hudiara drain using bore water and vegetables adjacent to the Hudiara drain. Toxic heavy metals badly affect human health because of industrial environmental contamination. Particularly hundreds of millions of individuals globally have faced the consequences of consuming water and food tainted with pollutants. Concentrations of heavy metals in human blood were elevated in Hudiara drainings in Lahore city, Pakistan, due to highly polluted industrial effluents. The study determined the health effects of high levels of heavy metals (Cd, Cu, Zn, Fe, Pb, Ni, Hg, Cr) on residents of the Hudiara draining area, including serum MDA, 8-Isoprostane, 8-hydroxyguanosine, and creatinine levels. An absorption spectrophotometer was used to determine heavy metals in wate water, drinking water, soil, plants and human beings blood sampleas and ELISA kits were used to assess the level of 8-hydroxyguanosine, MDA, 8-Isoprostane in plasma serum creatinine level. Waste water samples, irrigation water samples, drinking water samples, Soil samples, Plants samples and blood specimens of adult of different weights and ages were collected from the polluted area of the Hudiara drain (Laloo and Mohanwal), and control samples were obtained from the unpolluted site Sheiikhpura, 60 km away from the site. Toxic heavy metals in blood damage the cell membrane and DNA structures, increasing the 8-hydroxyguanosine, MDA, creatinine, and 8-Isoprostane. Toxic metals contaminated bore water and vegetables, resulting in increased levels of creatinine, MDA, Isoprostane, and 8-hydroxy-2-guanosine in the blood of inhabitants from the adjacent area Hudiara drain compared to the control group. In addition,. This study also investigated heavy metal concentrations in meat and milk samples from buffaloes, cows, and goats. In meat, cow samples showed the highest Cd, Cu, Fe and Mn concentrations. In milk also, cows exhibited elevated Cu and Fe levels compared to goats. The results highlight species-specific variations in heavy metal accumulation, emphasizing the need for targeted monitoring to address potential health risks. The significant difference between the two groups i.e., the control group and the affected group, in all traits of the respondents (weight, age, heavy metal values MDA, 8-Isoprostane, 8-hydroxyguaniosine, and serum creatinine level). Pearson's correlation coefficient was calculated. The study has shown that the level of serum MDA, 8-Isoprostane, 8-hydroxyguaniosine, or creatinine has not significantly correlated with age, so it is independent of age. This study has proved that in Pakistan, the selected area of Lahore in the villages of Laloo and Mohanwal, excess of heavy metals in the human body damages the DNA and increases the level of 8-Isoprostane, MDA, creatinine, and 8-hydroxyguaniosine. As a result, National and international cooperation must take major steps to control exposure to heavy metals.

All-cause, cardiovascular disease and cancer mortality in the population of a large Italian area contaminated by perfluoroalkyl and polyfluoroalkyl substances (1980-2018).

BACKGROUND: Per- and polyfluoroalkyl substances (PFAS) are associated with many adverse health conditions. Among the main effects is carcinogenicity in humans, which deserves to be further clarified. An evident association has been reported for kidney cancer and testicular cancer. In 2013, a large episode of surface, ground and drinking water contamination with PFAS was uncovered in three provinces of the Veneto Region (northern Italy) involving 30 municipalities and a population of about 150,000. We report on the temporal evolution of all-cause mortality and selected cause-specific mortality by calendar period and birth cohort in the local population between 1980 and 2018. METHODS: The Italian National Institute of Health pre-processed and made available anonymous data from the Italian National Institute of Statistics death certificate archives for residents of the provinces of Vicenza, Padua and Verona (males, n = 29,629; females, n = 29,518) who died between 1980 and 2018. Calendar period analysis was done by calculating standardised mortality ratios using the total population of the three provinces in the same calendar period as reference. The birth cohort analysis was performed using 20-84 years cumulative standardised mortality ratios. Exposure was defined as being resident in one of the 30 municipalities of the Red area, where the aqueduct supplying drinking water was fed by the contaminated groundwater. RESULTS: During the 34 years between 1985 (assumed as beginning date of water contamination) and 2018 (last year of availability of cause-specific mortality data), in the resident population of the Red area we observed 51,621 deaths vs. 47,731 expected (age- and sex-SMR: 108; 90% CI: 107-109). We found evidence of raised mortality from cardiovascular disease (in particular, heart diseases and ischemic heart disease) and malignant neoplastic diseases, including kidney cancer and testicular cancer. CONCLUSIONS: For the first time, an association of PFAS exposure with mortality from cardiovascular disease was formally demonstrated. The evidence regarding kidney cancer and testicular cancer is consistent with previously reported data.

A powerful method for In Situ and rapid detection of trace nanoplastics in water-Mie scattering.

The pervasive presence of nanoplastics (NPs) in environmental media has raised significant concerns regarding their implications for environmental safety and human health. However, owing to their tiny size and low level in the environment, there is still a lack of effective methods for measuring the amount of NPs. Leveraging the principles of Mie scattering, a novel approach for rapid in situ quantitative detection of small NPs in low concentrations in water has been developed. A limit of detection of 4.2 µg/L for in situ quantitative detection of polystyrene microspheres as small as 25 nm was achieved, and satisfactory recoveries and relative standard deviations were obtained. The results of three self-ground NPs showed that the method can quantitatively detect the concentration of NPs in a mixture of different particle sizes. The satisfactory recoveries (82.4% to 110.3%) of the self-ground NPs verified the good anti-interference ability of the method. The total concentrations of the NPs in the five brands of commercial bottled water were 0.07 to 0.39 µg/L, which were directly detected by the method. The proposed method presents a potential approach for conducting in situ and real-time environmental risk assessments of NPs on human and ecosystem health in actual water environments.

Variation of total alpha and beta activities and Rn-222 concentrations in the water supply system of an Italian volcanic region: How safe is tap water for human consumption?

Total alpha and beta activities and Rn-222 concentrations were determined in water from different sections of seven aqueducts belonging to the water supply system of Campania region (Italy), known worldwide for its volcanism. Statistical analysis was performed on data to account for their variability across the aqueduct sections, and results were discussed considering the geology of reservoirs, the potential mixing processes occurring along the pipe network, the building/constituting materials of the aqueduct sections, and the integrity of the infrastructure. Guidelines proposed by Italian and international regulation entities were considered to determine if total alpha and beta activities and Rn-222 concentrations found at the taps of the different aqueducts should be considered detrimental to public health. Based on a deterministic and a stochastic approach, a health risk assessment was also tested for Rn-222, assuming direct ingestion and showering as potential exposure pathways. Results showed that applying guidelines returned an absence of hazard, whereas risk assessment returned a high probability of exposure to unacceptable Rn-222 doses for some aqueducts. Beyond the usefulness of obtained results to plan actions to improve the safety of drinking water in Campania, our outcomes represent a warning for bodies dealing with public health at any level: the use of guidelines can bring an underestimation of the risks exerted by the exposure to Rn-222 on human health. Further, using a probabilistic approach in risk assessment accounting for uncertainty can favor risk forecasts based on more "realistic" scenarios.

Assessment of coastal river water quality in Bangladesh: Implications for drinking and irrigation purposes.

Saltwater intrusion in the coastal areas of Bangladesh is a prevalent phenomenon. However, it is not conducive to activities such as irrigation, navigation, fish spawning and shelter, and industrial usage. The present study analyzed 45 water samples collected from 15 locations in coastal areas during three seasons: monsoon, pre-monsoon, and post-monsoon. The aim was to comprehend the seasonal variation in physicochemical parameters, including water temperature, pH, electrical conductivity (EC), salinity, total dissolved solids (TDS), hardness, and concentrations of Na+, K+, Mg2+, Ca2+, Fe2+, HCO3-, PO43-, SO42-, and Cl-. Additionally, parameters essential for agriculture, such as soluble sodium percentage (SSP), sodium absorption ratio (SAR), magnesium absorption ratio (MAR), residual sodium carbonate (RSC), Kelly's ratio (KR), and permeability index (PI), were examined. Their respective values were found to be 63%, 16.83 mg/L, 34.92 mg/L, 145.44 mg/L, 1.28 mg/L, and 89.29%. The integrated water quality index was determined using entropy theory and principal component analysis (PCA). The resulting entropy water quality index (EWQI) and SAR of 49.56% and 63%, respectively, indicated that the samples are suitable for drinking but unsuitable for irrigation. These findings can assist policymakers in implementing the Bangladesh Deltaplan-2100, focusing on sustainable land management, fish cultivation, agricultural production, environmental preservation, water resource management, and environmental protection in the deltaic areas of Bangladesh. This research contributes to a deeper understanding of seasonal variations in the hydrochemistry and water quality of coastal rivers, aiding in the comprehension of salinity intrusion origins, mechanisms, and causes.

Peril in the Pipeline: Unraveling the threads of PFAS contamination in U.S. drinking water systems.

We examined the spatial distribution of Per- and Polyfluoroalkyl Substances (PFAS) in the US drinking water and explored the relationship between PFAS contamination, public water systems (PWS) characteristics, and socioeconomic attributes of the affected communities. Using data from the EPA's third Unregulated Contaminant Rule, the Census Bureau, and the Bureau of Labor Statistics, we identified spatial contamination hot spots and found that PFAS contamination was correlated with PWSs size, non-surface raw water intake sources, population, and housing density. We also found that non-white communities had less PFAS in drinking water. Lastly, we observed that PFAS contamination varied depending on regional industrial composition. The results showed that drinking water PFAS contamination was an externality of not only some industrial activities but also household consumption.

Microwell fluoride assay screening for enzymatic defluorination.

There is intense interest in removing fluorinated compounds from the environment, environments are most efficiently remediated by microbial enzymes, and defluorinating enzymes are readily monitored by fluoride determination. Fluorine is the most electronegative element. Consequently, all mechanisms of enzymatic C-F bond cleavage produce fluoride anion, F-. Therefore, methods for the determination of fluoride are critical for C-F enzymology and apply to any fluorinated organic compounds, including PFAS, or per- and polyfluorinated alkyl substances. The biodegradation of most PFAS chemicals is rare or unknown. Accordingly, identifying new enzymes, or re-engineering the known defluorinases, will require rapid and sensitive methods for measuring fluoride in aqueous media. Most studies currently use ion chromatography or fluoride specific electrodes which are relatively sensitive but low throughput. The methods here describe refashioning a drinking water test to efficiently determine fluoride in enzyme and cell culture reaction mixtures. The method is based on lanthanum alizarin complexone binding of fluoride. Reworking the method to a microtiter well plate format allows detection of as little as 4 nmol of fluoride in 200 µL of assay buffer. The method is amenable to color imaging, spectrophotometric plate reading and automated liquid handling to expedite assays with thousands of enzymes and/or substrates for discovering and improving enzymatic defluorination.

Prevalence and concentration of pesticides in European waters: A protocol for systematic review and meta-analysis.

There is currently a growing interest in the so-called emerging pollutants, such as pesticides, pharmaceuticals, personal hygiene care products, drugs, etc., whose presence in natural ecosystems is not necessarily recent, but the development in latest years of new and more sensitive methods of analysis has allowed their detection. They can be present in the natural environment, food, and many products of everyday origin, which suggests that human exposure to them is massive and universal. Therefore, the study of this type of substances is becoming one of the priority lines of research of the main agencies dedicated to the protection of public and environmental health, such as the World Health Organization (WHO), United States Environmental Protection Agency (USEPA) or European Union (EU). In this sense, it is of vital importance to know the nature and quantity of this type of contaminants, to establish preventive mechanisms that minimize its presence in aquatic systems, with special requirements for human consumption. This study aimed to describe a protocol for a systematic review and meta-analysis to assess the status of pesticides in European waters. We will search for original studies in the PubMed/Medline, Scopus, Web of Science, EMBASE, ScienceDirect databases. Prevalence studies of emerging contaminants (pesticides) in water resources (watersheds, aquifers, rivers, marine and springs), wastewaters (influent and effluent), and drinking water should be included. Two reviewers will independently screen and assess the included studies, with any disagreements being resolved by a third reviewer. We will summarize the findings using a narrative approach and, if possible, conduct a quantitative synthesis (meta-analysis). We will conduct the protocol following the Preferred Reporting Items for Systematic Review and Meta-Analyses Protocols (PRISMA-P) guidelines. The review will summarize the current evidence on the presence of pesticides in European waters such as glyphosate, chlorpyrifos, pyrethroid pesticides, neonicotinoid pesticides, and/or fungicides, in samples of different water resources like wastewaters and drinking water. We expect that this systematic review will establish preventive mechanisms that minimize the presence of pesticides in water in the environment.

Investigation of the protective effect of chitosan against arsenic-induced nephrotoxicity and oxidative damage in rat kidney tissue.

Arsenic is an important metalloid that can cause poisoning in humans and domestic animals. Exposure to arsenic causes cell damage, increasing the production of reactive oxygen species. Chitosan is a biopolymer obtained by deacetylation of chitin with antioxidant and metal ion chelating properties. In this study, the protective effect of chitosan on arsenic-induced nephrotoxicity and oxidative damage was investigated. 32 male Wistar-albino rats were divided into 4 groups of 8 rats each as control group (C), chitosan group (CS group), arsenic group (AS group), and arsenic+chitosan group (AS+CS group). The C group was given distilled water by oral gavage, the AS group was given 100 ppm/day Na-arsenite ad libitum with drinking water, the CS group was given 200 mg/kg/day chitosan dissolved in saline by oral gavage, the AS+CS group was given 100 ppm/day Na-arsenite ad libitum with drinking water and 200 mg/kg/day chitosan dissolved in saline by oral gavage for 30 days. At the end of the 30-day experimental period, 90 mg/kg ketamine was administered intraperitoneally to all rats, and blood samples and kidney tissues were collected. Urea, uric acid, creatinine, P, Mg, K, Ca, Na, Cystatin C (CYS-C), Neutrophil Gelatinase Associated Lipocalin (NGAL) and Kidney Injury Molecule 1 (KIM-1) levels were measured in serum samples. Malondialdehyde (MDA), Glutathione (GSH), Catalase (CAT) and Superoxide dismutase (SOD) levels in the supernatant obtained from kidney tissue were analyzed by ELISA method. Compared with AS group, uric acid and creatinine levels of the AS+CS group were significantly decreased (p<0.001), urea, KIM-1, CYS-C, NGAL, and MDA levels were numerically decreased and CAT, GSH, and SOD levels were numerically increased (p>0.05). In conclusion, based on both biochemical and histopathological-immunohistochemical- immunofluorescence findings, it can be concluded that chitosan attenuates kidney injury and protects the kidney.

Leaching behavior of metals from asphalt mixtures modified with crumb rubber from scrap tires.

There are concerns about the potential toxicity of bitumen and recycled materials such as reclaimed asphalt pavements from end-of-life roads and crumb rubber from scrap tires used in asphalt mixtures because they contain metals that may be released into the groundwater. This study investigated the potential metal leaching of laboratory-prepared asphalt mixtures modified with polymer coated rubber (PCR) with wet and dry technology, devulcanized rubber (DVR), compared to an unmodified control mixture and a blend modified with a synthetic polymer (SBS). The objectives were to i) quantify concentrations of metals released, ii) calculate the flux rate, the cumulative mass release, and the assessment ratio for each metal, iii) verify if the metals exceeded the EPA drinking water limit, and, finally, iv) assess the source of metals release. Zinc had the highest concentration among all metals and was present in eluates from all mixtures. The cumulative zinc concentration from DVR mixture was 41% and 34% higher than the control and SBS mixtures, respectively. For PCR wet, the cumulative zinc concentration was 9% higher than the control blend and 1% lower than the SBS mix. The assessment ratio indicated that all metal concentrations would not exceed the drinking water limit, except for zinc, for which further evaluations were required. The main source of zinc may derive from aggregates. This work showed that crumb rubber might not be the only source of metal leaching, and its use in asphalt pavements does not cause a metal leaching higher than other materials.

Geographical distribution of radon and associated health risks in drinking water samples collected from the Mulazai area of Peshawar, Pakistan.

Geospatial methods, such as GIS and remote sensing, map radon levels, pinpoint high-risk areas and connect geological traits to radon presence. These findings direct health planning, focusing tests, mitigation, and policies where radon levels are high. Overall, geospatial analyses offer vital insights, shaping interventions and policies to reduce health risks from radon exposure. There is a formidable threat to human well-being posed by the naturally occurring carcinogenic radon (222Rn) gas due to high solubility in water. Under the current scenario, it is crucial to assess the extent of 222Rn pollution in our drinking water sources across various regions and thoroughly investigate the potential health hazards it poses. In this regard, the present study was conducted to investigate the concentration of 222Rn in groundwater samples collected from handpumps and wells and to estimate health risks associated with the consumption of 222Rn-contaminated water. For this purpose, groundwater samples (n = 30) were collected from handpumps, and wells located in the Mulazai area, District Peshawar. The RAD7 radon detector was used as per international standards to assess the concentration of 222Rn in the collected water samples. The results unveiled that the levels of 222Rn in the collected samples exceeded the acceptable thresholds set by the US Environmental Protection Agency (US-EPA) of 11.1 Bq L-1. Nevertheless, it was determined that the average annual dose was below the recommended limit of 0.1 mSv per year, as advised by both the European Union Council and the World Health Organization. In order to avoid the harmful effects of such excessive 222Rn concentrations on human health, proper ventilation and storage of water in storage reservoirs for a long time before use is recommended to lower the 222Rn concentration.

Analysing N-nitrosamine occurrence and sources in karst reservoirs, Southwest China.

N-nitrosamines in reservoir water have drawn significant attention because of their carcinogenic properties. Karst reservoirs containing dissolved organic matter (DOM) are important drinking water sources and are susceptible to contamination because of the fast flow of various contaminants. However, it remains unclear whether N-nitrosamines and their precursor, DOM, spread in karst reservoirs. Therefore, this study quantitatively investigated the occurrence and sources of N-nitrosamines based on DOM properties in three typical karst reservoirs and their corresponding tap water. The results showed that N-nitrosamines were widely spread, with detection frequencies > 85%. Similar dominant compounds, including N-nitrosodimethylamine, N-nitrosomethylethylamine, N-nitrosopyrrolidine, and N-nitrosodibutylamine, were observed in reservoirs and tap water, with average concentrations of 4.7-8.9 and 2.8-6.7 ng/L, respectively. The average carcinogenic risks caused by these N-nitrosamines were higher than the risk level of 10-6. Three-dimensional fluorescence excitation-emission matrix modeling revealed that DOM was composed of humus-like component 1 (C1) and protein-like component 2 (C2). Fluorescence indicators showed that DOM in reservoir water was mainly affected by exogenous pollution and algal growth, whereas in tap water, DOM was mainly affected by microbial growth with strong autopoietic properties. In the reservoir water, N-nitrosodiethylamine and N-nitrosopiperidine were significantly correlated with C2 and biological indicators, indicating their endogenously generated sources. Based on the principal component analysis and multiple linear regression methods, five sources of N-nitrosamines were identified: agricultural pollution, microbial sources, humus sources, degradation processes, and other factors, accounting for 46.8%, 36.1%, 7.82%, 8.26%, and 0.96%, respectively. For tap water, two sources, biological reaction processes, and water distribution systems, were identified, accounting for 75.7% and 24.3%, respectively. Overall, this study presents quantitative information on N-nitrosamines' sources based on DOM properties in typical karst reservoirs and tap water, providing a basis for the safety of drinking water for consumers.

Analysis of the chemical characteristics and causes of high total hardness of groundwater in Jianghan Plain, China.

Familiarity with the chemical characteristics of regional groundwater can provide important guidance and reference for the development of regional groundwater exploitation. Jianghan Plain has been reported to have high groundwater total hardness (TH), resulting in the inability of local groundwater to be directly used as drinking water. In order to explore the causes of high TH, the paper analyzed the hydrochemical characteristics of shallow groundwater in Jianghan Plain combined with software of SPSS, JMP, and PHEEQC. The results showed that the cations in the groundwater in the area were mainly Ca2+, while the anions were mainly HCO3-. 20% of groundwater exceed the China national guideline for TH (i.e., 450 mg/L). The groundwater chemistry in the study area was controlled by three main factors of dissolution of carbonate rocks, human activities, and redox conditions, among which the interaction between water and rock had the greatest impact. The water carbonate rock interaction within Jianghan Plain was affected by various factors such as water flow and aquifers and showed a gradually weakening trend from west to east. This work not only strengthened the understanding of the causes of the high TH of groundwater in the region, but also provided reference value for regional groundwater environmental management.

Behavioural responses of beef cattle to different grazing systems and the influence of these responses on water productivity of livestock in a tropical savannah.

Environmental conditions and available forage on pastures greatly differ between different farming systems, which can affect the behaviour of grazing cattle. The interplay between environment-, forage-, and animal-related variables may affect the use of feed and water resources in grazing-based systems. Hence, our objectives were (i) to study the differences between grazing-based systems and seasons in environment- and pasture-related variables as well as the behaviour, feed intake, performance, and water productivity of Nellore heifers, and (ii) to understand the interrelationships between these variables. The measurements were performed in a conventional grazing system (CON), an integrated crop-livestock (ICL), and a crop-livestock-forestry (ICLF) systems in the Brazilian Cerrado during the rainy and dry seasons. Ambient temperature and relative air humidity were hourly measured in both seasons. Forage biomass and sward height were determined every month. Forage samples were taken to determine the proportions of alive leaves, alive stems, and dead plant material and to analyse their nutritive value. Forage intake, drinking water intake, and liveweight changes were quantified in 12 Nellore heifers per system and season. Feeding behaviour was recorded by chewing sensors on nine continuous days in each season. Drinking water intake was measured by water meters attached to drinking water troughs, whereby trial cameras at the troughs recorded the frequency of drinking events of individual animals. Feed conversion efficiency and water productivity were estimated. The ICLF reduced the exposure time to high ambient temperatures so that heifers even grazed during the hottest hours. Forage biomass in ICL and CON had greater proportions of stem and dead plant material than in ICLF. Forage intake rate was greater and grazing events were longer for animals in ICLF than those in CON, whereas the daily number of grazing events was greater in CON. Feed conversion efficiency and water productivity were greater in integrated systems than in CON. Amongst studied variables, thermal environment and forage canopy structure with its proportions of dead plant material are the main driving factors for animal behaviour, forage intake rate, and animal performance. These variables reduce feed conversion efficiency and water productivity in grazing cattle. Further research should analyse strategies for promoting thermal comfort for the animals, increasing the proportions of alive biomass, and enhancing the nutritional value of pastures for more efficient use of forage and water resources in grazing-based systems.

Microplastics in drinking water: A review on methods, occurrence, sources, and potential risks assessment.

Microplastics in drinking water captured widespread attention following reports of widespread detection around the world. Concerns have been raised about the potential adverse effects of microplastics in drinking water on human health. Given the widespread interest in this research topic, there is an urgent need to compile existing data and assess current knowledge. This paper provides a systematic review of studies on microplastics in drinking water, their evidence, key findings, knowledge gaps, and research needs. The data collected show that microplastics are widespread in drinking water, with large variations in reported concentrations. Standardized methodologies of sampling and analysis are urgently needed. There were more fibrous and fragmented microplastics, with the majority being <10 µm in size and composed of polyester, polyethylene, polypropylene, and polystyrene. Little attention has been paid to the color of microplastics. More research is needed to understand the occurrence and transfer of microplastics throughout the water supply chain and the treatment efficiency of drinking water treatment plants (DWTPs). Methods capable of analyzing microplastics <10 µm and nanoplastics are urgently needed. Potential ecological assessment models for microplastics currently in use need to be improved to take into account the complexity and specificity of microplastics.

Human biomonitoring of trace metals from different altitudinal settings of Pakistan.

Human biomonitoring of toxic trace elements is of critical importance for public health protection. The current study aims to assess the levels of selected trace metals (Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn) into paired human nail and hair samples (n = 180 each) from different altitudinal setting along the Indus River, and which were measured by using inductively coupled plasma mass spectrometry (ICP-MS). The human samples (hair and nail) were collected from four different ecological zones of Pakistan which include frozen mountain zone (FMZ), wet mountain zone (WMZ), riverine delta zone (RDZ), and low-lying southern areas (LLZ). Our results showed the following occurrence trends into studied hair samples: higher values (ppm) of Zn (281), Co (0.136), and Mn (5.65) at FMZ; Cr (1.37), Mn (7.83), and Ni (1.22) at WMZ; Co (0.15), Mn (11.89), and Ni (0.99) at RDZ; and Mn (8.99) and Ni (0.90) at LLZ. While in the case of nails, the levels (ppm) of Mn (9.91) at FMZ and Mn (9.38, 24.1, and 12.5), Cr (1.84, 3.87, and 2.33), and Ni (10.69, 8.89, and 12.6) at WMZ, RDZ and LLZ, respectively, showed higher concentration. In general, among the studied trace elements, Mn and Ni in hair/nail samples were consistently higher and exceeded the WHO threshold/published reference values in most of the studied samples (> 50-60%) throughout the Indus basin. Similarly, hair/nail Pb values were also higher in few cases (2-10%) at all studied zones and exceeded the WHO threshold/published reference values. Our area-wise comparisons of studied metals exhibited altitudinal trends for Cd, Cr, Zn, and Mn (p < 0.05), and surprisingly, the values were increasing from south to north (at higher altitudes) and indicative of geogenic sources of the studied toxic elements, except Mn, which was higher at lower floodplain areas. Estimated daily intake (EDI) values showed that food and drinking water had the highest contribution towards Zn, Cu, Mn, and Ni and accumulation at all studied zones. Whereas, dust also acts as the main exposure route for Mn, Co, Cr, and Cd followed by the food, and water.

Machine learning framework for predicting cytotoxicity and identifying toxicity drivers of disinfection byproducts.

Drinking water disinfection can result in the formation disinfection byproducts (DBPs, > 700 have been identified to date), many of them are reportedly cytotoxic, genotoxic, or developmentally toxic. Analyzing the toxicity levels of these contaminants experimentally is challenging, however, a predictive model could rapidly and effectively assess their toxicity. In this study, machine learning models were developed to predict DBP cytotoxicity based on their chemical information and exposure experiments. The Random Forest model achieved the best performance (coefficient of determination of 0.62 and root mean square error of 0.63) among all the algorithms screened. Also, the results of a probabilistic model demonstrated reliable model predictions. According to the model interpretation, halogen atoms are the most prominent features for DBP cytotoxicity compared to other chemical substructures. The presence of iodine and bromine is associated with increased cytotoxicity levels, while the presence of chlorine is linked to a reduction in cytotoxicity levels. Other factors including chemical substructures (CC, N, CN, and 6-member ring), cell line, and exposure duration can significantly affect the cytotoxicity of DBPs. The similarity calculation indicated that the model has a large applicability domain and can provide reliable predictions for DBPs with unknown cytotoxicity. Finally, this study showed the effectiveness of data augmentation in the scenario of data scarcity.